{"title":"Building Jigs","description":"\u003cp\u003eTools to help you build and setup your boat\u003c\/p\u003e","products":[{"product_id":"boom-drill-guide","title":"Boom Drill Guide","description":"\u003cp\u003eDrill guide blocks for precisely drilling boom holes for Z hooks. Available for in multiple measurement options.\u003c\/p\u003e\n\u003ch4\u003eFeatures\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003eAvailable for 10 mm and 11 mm booms\u003c\/li\u003e\n\u003cli\u003eEach block has holes a different spacing on each side. Option one has holes spaced at 5 mm and 4 mm. Option two has holes spaced at 2.5 mm and 3 mm\u003c\/li\u003e\n\u003cli\u003eReference hole on the bottom for drilling vang hole\u003c\/li\u003e\n\u003cli\u003e1.5 mm reference holes for drilling\u003c\/li\u003e\n\u003cli\u003eNylon thumb screw for solid positioning. Can be screwed from two sides for greater flexibility\u003c\/li\u003e\n\u003cli\u003eReference notch for easy alignment marking\u003c\/li\u003e\n\u003cli\u003eMeasurement specific colours for easy identification in the workshop.\u003c\/li\u003e\n\u003cli\u003ePrinted in PLA which is a bioplastic but has low heat resistance. May warp if left in direct sunlight or hot environments such as a hot car.\u003c\/li\u003e\n\u003cbr\u003e\n\u003c\/ul\u003e\n\u003ch4\u003eUsage instructions\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003eAlign the block to the boom using the reference notch. This is also useful to mark the boom for installation of other components.\u003c\/li\u003e\n\u003cli\u003ePosition the boom block where desired to drill holes for a Z hook.\u003c\/li\u003e\n\u003cli\u003eDo not over tighten the nylon lock as it may deform the mast.\u003c\/li\u003e\n\u003cli\u003eOptionally two drill blocks, or a mast drill block may be used to allow movement of the boom drill block while maintaining reference. With one block set as reference, lay the boom and block on a flat surface and align the second block to same flat surface. With one block tightened, the other may be moved without losing alignment reference.\u003c\/li\u003e\n\u003cli\u003eDrill carefully with a 1.5mm drill. Be careful to keep the drill aligned not to widen the reference holes. If the tool is used carefully it may be used to drill multiple booms before needing replacement.\u003c\/li\u003e\n\u003cli\u003eIf a larger hole is needed, drill a 1.5mm hole, remove the drill block and re-drill with a wider drill bit.\u003c\/li\u003e\n\u003cli\u003eFor positioning the vang hole consider the reference hole is 5 mm from the edge of the block.\u003c\/li\u003e\n\u003cbr\u003e\n\u003c\/ul\u003e\n\u003ch4\u003eSpecifications\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003eMaterial: 3d printed in PLA which is a bioplastic with low melting point and becomes soft at 50°C.\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eFixing screw: M6 nylon thumb screw\u003c\/li\u003e\n\u003cli\u003eDimensions: 34 mm tall, 24 mm wide, 50 mm long\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SailorMadeRC","offers":[{"title":"11 mm boom \/ 4 and 5 mm spacing","offer_id":58027281187151,"sku":"SM-DRILLBOOM-1145","price":5.0,"currency_code":"EUR","in_stock":true},{"title":"11 mm boom \/ 2.5 and 3 mm spacing","offer_id":58027281154383,"sku":"SM-DRILLBOOM-1123","price":5.0,"currency_code":"EUR","in_stock":true},{"title":"10 mm boom \/ 4 and 5 mm spacing","offer_id":58027281121615,"sku":"SM-DRILLBOOM-1045","price":5.0,"currency_code":"EUR","in_stock":true},{"title":"10 mm boom \/ 2.5 and 3 mm spacing","offer_id":58027281088847,"sku":"SM-DRILLBOOM-1023","price":5.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3010\/7727\/files\/SM-DRILLBOOM.MAIN.jpg?v=1778626249"},{"product_id":"mast-drill-guide","title":"Mast Drill Guides (pair)","description":"\u003cp\u003eDrill guide blocks for precisely drilling masts and aligning the gooseneck from various manufacturers. One pair in each set.\u003c\/p\u003e\n\u003ch4\u003eFeatures\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003eAccommodates 11 mm masts\u003c\/li\u003e\n\u003cli\u003eSupplied in pairs to maintain alignment reference while moving one of the blocks\u003c\/li\u003e\n\u003cli\u003eNylon thumb screw for solid positioning. Can be screwed from two sides for greater flexibility\u003c\/li\u003e\n\u003cli\u003eDrill guide holes on four faces at perfectly square angles\u003c\/li\u003e\n\u003cli\u003e1.5 mm holes for drilling\u003c\/li\u003e\n\u003cli\u003eReference notches for marking and aligning holes to measurement references\u003c\/li\u003e\n\u003cli\u003eGooseneck alignment guides fit 2, 3, 4 and 5.5 mm pins allowing for precise alignment of goosenecks from different suppliers. Tested with SAILSetc and PG Modelisme models.\u003c\/li\u003e\n\u003cli\u003eOrange colour for easy visibility in the workshop.\u003c\/li\u003e\n\u003cli\u003ePrinted in PLA which is a bioplastic but has low heat resistance. May warp if left in direct sunlight or hot environments such as a hot car.\u003c\/li\u003e\n\u003cbr\u003e\n\u003c\/ul\u003e\n\u003ch4\u003eUsage instructions\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003eIf working on a pre-bent mast, align one block to the fore or aft bend marking and lock down.\u003c\/li\u003e\n\u003cli\u003eDo not over tighten the nylon lock as it may deform the mast.\u003c\/li\u003e\n\u003cli\u003eIf working with an unbent mast that will be bent, fix one block to the base of the mast and use it as reference while bending the mast. This way the block will be perfectly aligned to the mast bend direction.\u003c\/li\u003e\n\u003cli\u003eWith one block set as reference, lay the mast and block on a flat surface and align the second block to same flat surface. With one block tightened, the other may be moved without losing alignment reference.\u003c\/li\u003e\n\u003cli\u003eUse the side notches to measure the positions for forestay and shrouds. Alternatively build a reference ruler with markings for bands and holes. Use the side notches to align the drilling holes to the markings on the ruler.\u003c\/li\u003e\n\u003cli\u003eDrill carefully with a 1.5mm drill. Be careful to keep the drill aligned not to widen the reference holes. If the tool is used carefully it may be used to drill multiple masts before needing replacement.\u003c\/li\u003e\n\u003cli\u003eIf a larger hole is needed, drill a 1.5mm hole, remove the drill block and re-drill with a wider drill bit. Alternatively carefully drill the block with a wider bit to widen the reference hole.\u003c\/li\u003e\n\u003cli\u003eTo align a gooseneck:\n\u003cul\u003e\n\u003cli\u003eCheck which ends of the gooseneck fit into the reference guides. Some models require removing the boom end fitting. Some models will align using the screw that holds the boom end fitting.\u003c\/li\u003e\n\u003cli\u003eThe pin or screw on the gooseneck should fit snugly into the alignment groove. Add tape to both sides of the groove if a tighter fit is desired.\u003c\/li\u003e\n\u003cli\u003eCheck if your gooseneck can be supported by two blocks, from either side, for greater support\u003c\/li\u003e\n\u003cli\u003eWith one block still serving as an alignment reference on the mast, position the second block so it holds the gooseneck in place and aligned to the mast bend and drilled holes. Tighten the block\u003c\/li\u003e\n\u003cli\u003eIf your gooseneck can be supported by a second block on the other end, move a free block to this position and tighten. The gooseneck should be firmly in place for drilling.\u003c\/li\u003e\n\u003cli\u003eOptionally, for added stability while drilling, place a few dots of cyanoacrylate glue to hold the gooseneck in place, or temporarily tie it down with zip ties.\u003c\/li\u003e\n\u003cli\u003eCarefully drill the gooseneck and mast as instructed by the manufacturer.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cbr\u003e\n\u003c\/ul\u003e\n\u003ch4\u003eSpecifications\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003eMaterial: 3d printed in PLA which is a bioplastic with low melting point and becomes soft at 50°C.\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eFixing screw: M6 nylon thumb screw\u003c\/li\u003e\n\u003cli\u003eDimensions: 34 mm cube\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SailorMadeRC","offers":[{"title":"Default Title","offer_id":57678270824783,"sku":"SM-DRILLMAST-11","price":10.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3010\/7727\/files\/SM-DRILLMAST-11.MAIN.jpg?v=1778626251"},{"product_id":"weighing-support","title":"Weighing Support","description":"\u003cp\u003eAll racing RC sailboats must conform to strict weight limitations. Our support holds your boat in place for precise weighing, either at home, at the workshop, or used by judges to certify boats before regattas.\u003c\/p\u003e\n\u003cp\u003eJust slip the bulb and keel into the support and it will balance perfectly. The low center of gravity of the boats, due the the ballast, will keep even a fully rigged IOM stable for weighing. EVA foam padding protects the bulb and fin from any scratches.\u003c\/p\u003e\n\u003cp\u003eThe support can also be used as a stand to display your hull on a shelf.\u003c\/p\u003e\n\u003cp\u003eColors will vary according to stock availability and are not selectable. Gray is a common color for this item but not guaranteed. If color is critically important, send us a note and we can check possibilites.\u003c\/p\u003e\n\u003cp\u003eIncludes parts printed in PLA which has low heat resistance and may warp if left in direct sunlight or hot environments such as a hot car.\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003ch4\u003eSpecifications\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003eFits: IOM, RG65, DF 65, DF 95, Micro Magic and other similar models\u003c\/li\u003e\n\u003cli\u003eMaximum bulb width: 48mm\u003c\/li\u003e\n\u003cli\u003eConstruction: 3d Printed PLA, PVC pipe and adhesive EVA foam. PLA is a bioplastic with low melting point and becomes soft at 50°C.\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eLength: 15 cm\u003c\/li\u003e\n\u003cli\u003eWidth: 8 cm\u003c\/li\u003e\n\u003cli\u003eHeight: 22 cm\u003c\/li\u003e\n\u003cli\u003eWeight: 190 g\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SailorMadeRC","offers":[{"title":"Default Title","offer_id":57678270857551,"sku":"SM-WEIGH-U","price":25.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3010\/7727\/files\/SM-WEIGH-U.MAIN.jpg?v=1778626309"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3010\/7727\/collections\/SM-DRILLMAST-11.PT07.jpg?v=1781786604","url":"https:\/\/sailormaderc.com\/collections\/building-jigs.oembed","provider":"SailorMadeRC","version":"1.0","type":"link"}